Search
You can find the results of your search below.
Fulltext results:
- Tire Pressure Sensor Code @projects:electronics:tirepressuresensor
- acros * ; ******************************* Bin_Out macro Floc ; Output a Binary Value variable i i = 0 while i < 8 if (i==4) movlw ' ' #i... movf _Error,F,A ; If _Error is set, change output to --- btfsc STATUS,Z goto noerr MOVL... nk movf _Error,F,A ; If _Error is set, change output to --- btfsc STATUS,Z goto No_Error m
- Panel Meter Interface @projects:electronics
- re shutdown| |7|AVss|Analog ground| |8|VoutA|DACa Output| **PIC Assembly Code** <code asm> SPIclk m... endm ;Setup direction BCF TRISB,RB1 ; RB1 as Output BCF TRISC,SCL ; SDO as Output BCF TRISC,SDA ; SCK as Output ;Set initial pin states BSF PORTB,RB1 ;Chip Select, active low
- Stepper motor driver @projects:electronics
- _con.jpg?400|}} ^DB9^Connection^ |1|L298-Pin14-Output 4| |2|L298-Pin13-Output 3| |3|L298-Pin3-Output 2| |4|L298-Pin2-Output 1| |5|Ground?| |6|Logic?| |7|Logic?| |8|Logic?| |9|Logic?| ====== Stepper
- Lenovo T530 Laptop WiFi upgrade
- emoval|www.bios-mods.com]] but I wanted to figure out how to modify the whitelist myself and to only us... e it work myself. (Also, I'd still need to figure out the bios reading and writing) VID:PID's * Inte... At this point I cleaned as I went, cleaning dust out of crevices & such. - Clean off the existin
- WET610N
- 1.8V Vdd Output: 1.793 2.5V Vdd Output: 2.531 ... Out: serial
- 50 Amp 5 Volt Power Supply @projects:electronics
- |}} Need a 208.76 ohm, 1% resistor to set the 5V output. Right now I'm using a 500 ohm potentiometer. 200 ohms would output 5.02V. {{:projects:electronics:50a5vpowersupp
- DGPS-11 Beacon Receiver @projects:electronics
- to 31.2VDC| | Orange|RS-232C In| | White|RS-232C Out| | Black|- Negative| | Blue|TTL Out| | Green|Data Ground| | Brown|Shield Ground| How can I tell if
- IO Board @projects:electronics
- Board ====== 16 Bit Digital input, 16 Bit Digital Output. {{:projects:electronics:ioboard:io_board.jpg?600|}} ===== Outputs ===== 16 Relays ====== Inputs ====== {{:pr
- Relay board @projects:electronics
- _details.aspx?cid=4&item=G4ODC5|G4 ODC5]] - G4 DC Output 5-60 VDC, 5 VDC Logic * [[http://www.opto22.... _details.aspx?cid=4&item=G4OAC5|G4 OAC5]] - G4 AC Output 12-140 VAC, 5 VDC Logic Want * [[http://www.
- SD GPS Track Logger @projects:electronics
- unction^I/O^Pin^Description^ |SCK|O|RB1|SPI Clock Out| |SDI|I|RB0|SPI Data In| |SDO|O|RC7|SPI Data Out| |CD|I|RB4|Physical Card Insertion Detect Signal| |WD
- C.H.I.P Computer
- 602 V </code> ==== Notes ==== Some of the voltage outputs are programmable via registers, so it appears
- Camera Flash Control
- ol unit 80px has a thyristor and adjustable light output. [[http://www.camerasunderwater.info/engineer
- GPS @projects:electronics
- mate Hyperformance GPS Receiver - Rockwell binary output only * [[http://byonics.com/gst-1/|GST-1
- Tire Pressure Sensor @projects:electronics
- heet to graph the transfer function, then working out the math to something which can be easily done in
- X10 Interfacing @projects:electronics
- few years (on three units I've used) so I figured out the pinout. 4N35's are used internally for opto-i