out

Search

You can find the results of your search below.

Fulltext results:

Tire Pressure Sensor Code @projects:electronics:tirepressuresensor
5 Hits, Last modified:
acros * ; ******************************* Bin_Out macro Floc ; Output a Binary Value variable i i = 0 while i < 8 if (i==4) movlw ' ' #i... movf _Error,F,A ; If _Error is set, change output to --- btfsc STATUS,Z goto noerr MOVL... nk movf _Error,F,A ; If _Error is set, change output to --- btfsc STATUS,Z goto No_Error m
Panel Meter Interface
4 Hits, Last modified:
re shutdown| |7|AVss|Analog ground| |8|VoutA|DACa Output| **PIC Assembly Code** <code asm> SPIclk m... endm ;Setup direction BCF TRISB,RB1 ; RB1 as Output BCF TRISC,SCL ; SDO as Output BCF TRISC,SDA ; SCK as Output ;Set initial pin states BSF PORTB,RB1 ;Chip Select, active low
Stepper motor driver
4 Hits, Last modified:
_con.jpg?400|}} ^DB9^Connection^ |1|L298-Pin14-Output 4| |2|L298-Pin13-Output 3| |3|L298-Pin3-Output 2| |4|L298-Pin2-Output 1| |5|Ground?| |6|Logic?| |7|Logic?| |8|Logic?| |9|Logic?| ====== Stepper
50 Amp 5 Volt Power Supply
2 Hits, Last modified:
|}} Need a 208.76 ohm, 1% resistor to set the 5V output. Right now I'm using a 500 ohm potentiometer. 200 ohms would output 5.02V. {{:projects:electronics:50a5vpowersupp
DGPS-11 Beacon Receiver
2 Hits, Last modified:
to 31.2VDC| | Orange|RS-232C In| | White|RS-232C Out| | Black|- Negative| | Blue|TTL Out| | Green|Data Ground| | Brown|Shield Ground| How can I tell if
IO Board
2 Hits, Last modified:
Board ====== 16 Bit Digital input, 16 Bit Digital Output. {{:projects:electronics:ioboard:io_board.jpg?600|}} ===== Outputs ===== 16 Relays ====== Inputs ====== {{:pr
Relay board
2 Hits, Last modified:
_details.aspx?cid=4&item=G4ODC5|G4 ODC5]] - G4 DC Output 5-60 VDC, 5 VDC Logic * [[http://www.opto22.... _details.aspx?cid=4&item=G4OAC5|G4 OAC5]] - G4 AC Output 12-140 VAC, 5 VDC Logic Want * [[http://www.
SD GPS Track Logger
2 Hits, Last modified:
unction^I/O^Pin^Description^ |SCK|O|RB1|SPI Clock Out| |SDI|I|RB0|SPI Data In| |SDO|O|RC7|SPI Data Out| |CD|I|RB4|Physical Card Insertion Detect Signal| |WD
GPS
1 Hits, Last modified:
mate Hyperformance GPS Receiver - Rockwell binary output only * [[http://byonics.com/gst-1/|GST-1
Tire Pressure Sensor
1 Hits, Last modified:
heet to graph the transfer function, then working out the math to something which can be easily done in
X10 Interfacing
1 Hits, Last modified:
few years (on three units I've used) so I figured out the pinout. 4N35's are used internally for opto-i