Search
You can find the results of your search below.
Fulltext results:
- Lenovo T530 Laptop WiFi upgrade
- emoval|www.bios-mods.com]] but I wanted to figure out how to modify the whitelist myself and to only us... e it work myself. (Also, I'd still need to figure out the bios reading and writing) VID:PID's * Inte... nected AC adaptor (this way I can apply power without accidentally jostling anything) - Plug AC ada... At this point I cleaned as I went, cleaning dust out of crevices & such. - Clean off the existin
- C.H.I.P Computer
- 899.625mA VBAT: 4.2075 V Charging at 633.0mA Vout: 4.3876 V </code> with -a switch <code> root@chip... 899.625mA VBAT: 4.2119 V Charging at 633.0mA Vout: 4.5962 V </code> 100mA USB current limit (Causi... 100.500mA VBAT: 4.1371 V Discharging at 68.5mA Vout: 4.1006 V </code> Fully charged <code> root@chip... V 251.625mA VBAT: 4.1910 V Discharging at 0mA Vout: 4.9602 V </code> ==== Notes ==== Some of the vol
- 405nm Laser Diode
- | |4.4| |50.0|4.41|5.7| |60.0|4.52|9.8| ===== Pinout ===== {{:projects:405nmlaser:ldpinout.gif?100|}} ^Pin^Description^ |1|Anode(+)| |2|Case Ground| |3|Cat... serdio.htm#diodct2|Determining the Laser Diode Pinout]] * [[http://repairfaq.cis.upenn.edu/sam/laserd
- DGPS-11 Beacon Receiver @projects:electronics
- to 31.2VDC| | Orange|RS-232C In| | White|RS-232C Out| | Black|- Negative| | Blue|TTL Out| | Green|Data Ground| | Brown|Shield Ground| How can I tell if... Look for a "D" in your Latitude/Longitude readout. ====== DGPS Beacon Receiver ====== I found an
- Camera Flash Control
- ra Flash Control ====== {{:projects:flash:iso_pinout.jpg|}} ^Cable^Shoe^Function?^Voltage^Wire^ |Shi... -minolta/flashcomp_techref.php#oldshoe|Hotshoe Pinout]] [[http://www.snowcat.de/flashcontroller/|Nik
- Fixing a Garmin USB charging cable
- USB charging cable ====== {{ :projects:miniusbpinout.png|Miniusb Pinout}} ^Pin^Function^ |1|5v Power| |2|n/a| |3|n/a| |4|17.3K to Ground| |5|Ground|
- MySensor board @projects:electronics
- sensors:mysensor_board.jpg?400|}} After reading about the [[http://mysensors.org/|MySensors project]], ... L><BR CLEAR="ALL"></HTML> ===== Components and layout ===== I'm using prebuilt modules for the Arduino ... nnections** * 1 x I2C * 2 x 1-wire * 2 breakout connectors for most of the remaining IO pins ^Qt
- Panel Meter Interface @projects:electronics
- ovwf DAC,A movlw 0x00 movwf DAC+1,A CALL SPIclkout CALL Delay goto myloop ; ================= ; === Functions === ; ================= SPIclkout BCF PORTB,RB1 ; Clear CS (Active low) BCF POR
- SD GPS Track Logger @projects:electronics
- unction^I/O^Pin^Description^ |SCK|O|RB1|SPI Clock Out| |SDI|I|RB0|SPI Data In| |SDO|O|RC7|SPI Data Out| |CD|I|RB4|Physical Card Insertion Detect Signal| |WD
- X10 Interfacing @projects:electronics
- few years (on three units I've used) so I figured out the pinout. 4N35's are used internally for opto-isolation, The power is from a transformer internally,
- WET610N
- Out: serial
- 7-segment display module @projects:electronics
- ount boards. I made this board using Eagle for layout and then I used [[http://www.batchpcb.com|BatchPC
- Barometric Pressure sensor @projects:electronics
- nsor:max3221-max3243.pdf|}} ==== MAX233CPP Breakout board ==== ^Wire^Function^ |Red|5V| |Yellow|RX (D
- IO Board @projects:electronics
- , rated for 5 to 240 Volts, AC or DC. ====== Pinout ====== ^Relay board^Signal Name^Pin^#^Pin^Signal
- Relay board @projects:electronics
- s:electronics:relayboard:relay_board.pdf|Board layout}} <HTML><BR CLEAR="ALL"></HTML> ====== OptoR