Search
You can find the results of your search below.
Fulltext results:
- Tire Pressure Sensor Code @projects:electronics:tirepressuresensor
- acros * ; ******************************* Bin_Out macro Floc ; Output a Binary Value variable i i = 0 while i < 8 if (i==4) movlw ' ' #i... 0x000008 ; High Priority ISR (Interrupt Service Routine) vector ; Start of High Priority ISR ... of subsequent instructions. If an interrupt ; routine alters their value(s) then when the program re
- Panel Meter Interface
- HDN|Hardware shutdown| |7|AVss|Analog ground| |8|VoutA|DACa Output| **PIC Assembly Code** <code asm> SPIclk macro BSF PORTC,SCK BCF PORTC,SCK endm ;Setup direction BCF TRISB,RB1 ; RB1 as Output BCF TRISC,SCL ; SDO as Output BCF TRISC,SDA ; SCK as Output ;Set initial pin states BSF POR
- Stepper motor driver
- _con.jpg?400|}} ^DB9^Connection^ |1|L298-Pin14-Output 4| |2|L298-Pin13-Output 3| |3|L298-Pin3-Output 2| |4|L298-Pin2-Output 1| |5|Ground?| |6|Logic?| |7|Logic?| |8|Logic?| |9|Logic?| ====== Stepper
- DGPS-11 Beacon Receiver
- to 31.2VDC| | Orange|RS-232C In| | White|RS-232C Out| | Black|- Negative| | Blue|TTL Out| | Green|Data Ground| | Brown|Shield Ground| How can I tell if... Look for a "D" in your Latitude/Longitude readout. ====== DGPS Beacon Receiver ====== I found an
- IO Board
- Board ====== 16 Bit Digital input, 16 Bit Digital Output. {{:projects:electronics:ioboard:io_board.jpg?600|}} ===== Outputs ===== 16 Relays ====== Inputs ====== {{:pr... , rated for 5 to 240 Volts, AC or DC. ====== Pinout ====== ^Relay board^Signal Name^Pin^#^Pin^Signal
- MySensor board
- sensors:mysensor_board.jpg?400|}} After reading about the [[http://mysensors.org/|MySensors project]], ... L><BR CLEAR="ALL"></HTML> ===== Components and layout ===== I'm using prebuilt modules for the Arduino ... nnections** * 1 x I2C * 2 x 1-wire * 2 breakout connectors for most of the remaining IO pins ^Qt... ad/EEPROM_read.ino|EEPROM reader]] - for debugging purposes, to find the node ID, parent, route, etc...
- Relay board
- s:electronics:relayboard:relay_board.pdf|Board layout}} <HTML><BR CLEAR="ALL"></HTML> ====== OptoR... _details.aspx?cid=4&item=G4ODC5|G4 ODC5]] - G4 DC Output 5-60 VDC, 5 VDC Logic * [[http://www.opto22.... _details.aspx?cid=4&item=G4OAC5|G4 OAC5]] - G4 AC Output 12-140 VAC, 5 VDC Logic Want * [[http://www.
- 50 Amp 5 Volt Power Supply
- |}} Need a 208.76 ohm, 1% resistor to set the 5V output. Right now I'm using a 500 ohm potentiometer. 200 ohms would output 5.02V. {{:projects:electronics:50a5vpowersupp
- SD GPS Track Logger
- unction^I/O^Pin^Description^ |SCK|O|RB1|SPI Clock Out| |SDI|I|RB0|SPI Data In| |SDO|O|RC7|SPI Data Out| |CD|I|RB4|Physical Card Insertion Detect Signal| |WD
- X10 Interfacing
- few years (on three units I've used) so I figured out the pinout. 4N35's are used internally for opto-isolation, The power is from a transformer internally,
- 7-segment display module
- ount boards. I made this board using Eagle for layout and then I used [[http://www.batchpcb.com|BatchPC
- Barometric Pressure sensor
- nsor:max3221-max3243.pdf|}} ==== MAX233CPP Breakout board ==== ^Wire^Function^ |Red|5V| |Yellow|RX (D
- GPS
- mate Hyperformance GPS Receiver - Rockwell binary output only * [[http://byonics.com/gst-1/|GST-1
- Serial Converter
- 233CPP * Uses no external caps ===== Cable Pinout ===== ^Pin ^Wire Colour ^Description ^ |1 |N/C |
- Temperature sensing devices
- pins 7 & 8 {{:projects:electronics:adt7410_pinout.png?600|}} From [[http://www.analog.com/en/senso