https://www.photonicsguy.ca/ 2026-04-06T22:14:03+00:00 https://www.photonicsguy.ca/ https://www.photonicsguy.ca/_media/wiki/dokuwiki.svg text/html 2014-11-13T18:50:14+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/tirepressuresensor/code?rev=1415904614&do=diff Tire Pressure Sensor Code Return to Tire Pressure Sensor Project. ;############################################################################### ;# TITLE "Pressure Sense" ;# ;# Program : Pressure sensor using an MPX5700DP sensor and LCD display ;# Version :1.0 ;# Revision Date : ;# Author : Jeff Brown ;# ;# ;# ;############################################################################### ; radix hex #define RA0_… text/html 2014-11-13T18:50:14+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/panelmeter?rev=1415904614&do=diff Panel Meter Interface Components * Panel Meter * [MCP41050] * [LM321] * [MAX5487 Digital Pot] * [12-bit DAC with SPI Interface] 1mA Full scale meter 94 Ohms coil resistance 5K Ohm resistor @ 5V = 1mA MCP4821 Pin No.SymbolFunction1VddSupply (2.7 to 5.5V)2CSChip Select3SCKSerial Clock Input4SDISerial Data Input text/html 2014-11-13T22:12:24+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/dualpressuresensor?rev=1415916744&do=diff Barometric Pressure sensor Dual pressure sensor board [PIC18F1320 Datasheet] RX on pin 3 TX on pin 2 Power ON 98.97 kPa, 742.3 Torr ; 0814,0521 98.97 kPa, 742.3 Torr ; 0814,0521 98.97 kPa, 742.3 Torr ; 0814,0521 Reference Barometer - MPXAZ4115A text/html 2016-03-09T02:48:00+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/mysensors?rev=1457491680&do=diff MySensor board After reading about the MySensors project, I decided to design a small circuit board to hold the Arduino and radio module. Status: * Nov 25th: I've assembled two working boards. Imgur photos * Nov 24th: I received the boards, Yay!! * Nov 7th, 2014: I'm waiting on the PCB's from text/html 2014-11-13T18:50:14+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/sdgpslogger?rev=1415904614&do=diff SD GPS Track Logger Why? This is why:Bicycling Trips ICSP Connector Need a PIC18 chip with more memory, I'm using the PIC18F4685 with 96Kbytes of program memory. Microchip Mass Storage Class Firmware [Still not working] Still not working. Might be software or hardware, I'll need to check it on a digital oscilloscope. Correct clock rate (less than 400KHz). text/html 2014-11-13T22:37:16+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/7segdisplay?rev=1415918236&do=diff 7-segment display module [Working Display] Arduino library available on Github This was one of my first doublesided and surfacemount boards. I made this board using Eagle for layout and then I used BatchPCB to manufacture the board. The board operates correctly, however, if I were to revise it, I would use a larger SMT resistor than the 0402 size. The board will be controlled via I2C from a PIC microcontroller, initially for the pressure sensor and later for other projects. text/html 2016-03-09T00:46:23+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/sumppump?rev=1457484383&do=diff Sump pump Monitor My parents have a cistern and a sump pump which would be useful to have some sort of water level monitoring. In the past, we would check the cistern level with a pressure gauge calibrated in inches of water. There was a rubber squeeze bulb which which would pressurize a plastic line which fed into the cistern, and the resulting level would be shown on the gauge.