Photonicsguy.ca

Fluke 189/187/89-IV/87-IV Remote Interface Specification

Anonymous (anonymous@undisclosed.example.com) — 2014-11-13T18:50:14+00:00

Fluke 189/187/89-IV/87-IV Remote Interface Specification Archive of http://www.cfa.harvard.edu/~thunter/manuals/RemoteSpec89_18X.htm Retrieved October 2009 from Internet Archive, dated September 13th, 2006. Technical Note Fluke is providing this information to those few customers who would like this information. We give this information with the understanding that Fluke will not provide any additional support on this information. This means that our Product Support Service will not be able t…

Embedded Linux computer with 1-wire net

Anonymous (anonymous@undisclosed.example.com) — 2017-11-12T18:33:58+00:00

Embedded Linux computer with 1-wire net Linksys NSLU2 running Debian Linux off of flash memory, polls a 1-wire net every 5 minutes and records the data (temperature and humidity) to a remote SQL server. 1-Wire PIC18 Microcontroller PIC18F4523 reading an ADT7410 temperature sensor via I2C.

Sump pump Monitor

Anonymous (anonymous@undisclosed.example.com) — 2016-03-09T00:46:23+00:00

Sump pump Monitor My parents have a cistern and a sump pump which would be useful to have some sort of water level monitoring. In the past, we would check the cistern level with a pressure gauge calibrated in inches of water. There was a rubber squeeze bulb which which would pressurize a plastic line which fed into the cistern, and the resulting level would be shown on the gauge.

Anonymous (anonymous@undisclosed.example.com) — 2014-11-13T20:00:07+00:00

To prevent spam, please use the following link.

” class=“wikilink1” onclick=“window.open('\075018UqgY9P-Qm-POT_xjvVdgg\75\75\46c\0752ns43EXefMfYkmDC4GrGsu6NOAFU6OZzu0o9jyOODCE\075', '', 'toolbar=0,scrollbars=0,location=0,statusbar=0,menubar=0,resizable=0,width=500,hei…

Anonymous (anonymous@undisclosed.example.com) — 2014-11-13T18:50:14+00:00
E-mail: ” onclick=“window.open('\07501tVyRJQeRv0b0Ha_nc2-JrA\75\75\46c\75OjytmEaPBjEYw66AkzhXoDVJUL9FEpgdlKKLq0uwCcg\075', '', 'toolbar=0,scrollbars=0,location=0,statusbar=0,menubar=0,resizable=0,width=500,height=300'); return false;

PHP

Anonymous (anonymous@undisclosed.example.com) — 2014-11-13T18:50:14+00:00
PHP IP print “Your IP is ”.$_SERVER[“REMOTE_ADDR”].“
\n”; Print “Server IP is ”.$_SERVER[“SERVER_ADDR”].“
\n”; ---------- Other $x=5; $y=8; $z=3; Print “X=$x\nY=$y\n
\nX+Y=”.($x+$y).“\n”

MBED

Anonymous (anonymous@undisclosed.example.com) — 2014-11-13T18:50:14+00:00
MBED Ethernet Magjack - [lU1S516LF Datasheet] [Pinout] PinmbedP1RD+P2RD-P3VccP4n/cP5n/cP6VccP7TD+P8TD-

First Project - Halloween Window Setup Light Sensor Possible IC to use: IVC102

OpenSCAD

Anonymous (anonymous@undisclosed.example.com) — 2016-03-09T03:23:15+00:00
OpenSCAD Endcap Endcap for a clear plexiglass tube to hold an LCD display module
Drive Pulley Pulley for a drive belt for a Kodak Slide projector

CadSoft EAGLE Libraries

Anonymous (anonymous@undisclosed.example.com) — 2021-07-06T13:33:14+00:00
CadSoft EAGLE Libraries eBay parts Footprints for components I've bought from eBay * eBay search for Arduino pro mini * eBay search for nrf24l01+ module Arduini mini pro NRF24L01+ module I've included a keepout block to prevent ground planes or traces from being routed under the antenna. I'm using this module for

Notes

Anonymous (anonymous@undisclosed.example.com) — 2014-11-13T18:50:14+00:00
Notes APC Environmental card AP9512TH IC1LM35Temperature SensorIC2LM358NDual OpampIC3LM78LVreg, 5VBP1[TDK CHS-UGR]Humidity Sensor AP9612 IC1ADC08348-Bit Serial I/O A/D Converter with Multiplexer OptionIC2MM74HC14NHex inverting Schmitt triggerIC5P87C521 Controller PCF8574 - 8-Bit I/O Expander for I2C-Bus

Vehicle

Anonymous (anonymous@undisclosed.example.com) — 2014-11-13T18:50:14+00:00
Vehicle If I only had a single wrench, I hope it's 13mm. 10mm for thermostat bracket bolts. Remote Starter Does not engage A/C, rear defroster. Horn is not connected either (for programming). Rear Defroster relay [Relay] ContactNote85Coil - Switched by ECM, ground to activate

Navy Island

Anonymous (anonymous@undisclosed.example.com) — 2021-07-06T13:59:08+00:00
Navy Island View my Navy Island pictures. Open in fullscreen
<article> <h1>MySensor board</h1> <p>Anonymous (anonymous@undisclosed.example.com) — 2016-03-09T02:48:00+00:00</p> MySensor board After reading about the MySensors project, I decided to design a small circuit board to hold the Arduino and radio module. Status: * Nov 25th: I've assembled two working boards. Imgur photos * Nov 24th: I received the boards, Yay!! * Nov 7th, 2014: I'm waiting on the PCB's from </article> <article> <h1>Relay board</h1> <p>Anonymous (anonymous@undisclosed.example.com) — 2014-11-13T18:50:14+00:00</p> Relay board SPDT JW1FEN relays from an old UPS. Matches closest to Digikey Part# 255-1114-ND [JW Relay datasheet] [Schematic] [Board layout] <HTML><BR CLEAR=“ALL”></HTML> OptoRelay Board G4PB16 - G4 16-channel I/O Module Rack * G4 ODC5 - G4 DC Output 5-60 VDC, 5 VDC Logic * G4 OAC5 - G4 AC Output 12-140 VAC, 5 VDC Logic </article> <article> <h1>SD GPS Track Logger</h1> <p>Anonymous (anonymous@undisclosed.example.com) — 2014-11-13T18:50:14+00:00</p> SD GPS Track Logger Why? This is why:Bicycling Trips ICSP Connector Need a PIC18 chip with more memory, I'm using the PIC18F4685 with 96Kbytes of program memory. Microchip Mass Storage Class Firmware [Still not working] Still not working. Might be software or hardware, I'll need to check it on a digital oscilloscope. Correct clock rate (less than 400KHz). </article> </main></body></html>