https://www.photonicsguy.ca/ 2026-04-06T20:35:43+00:00 https://www.photonicsguy.ca/ https://www.photonicsguy.ca/_media/wiki/dokuwiki.svg text/html 2016-03-09T02:48:00+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/mysensors?rev=1457491680&do=diff MySensor board After reading about the MySensors project, I decided to design a small circuit board to hold the Arduino and radio module. Status: * Nov 25th: I've assembled two working boards. Imgur photos * Nov 24th: I received the boards, Yay!! * Nov 7th, 2014: I'm waiting on the PCB's from text/html 2016-03-09T00:46:23+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/sumppump?rev=1457484383&do=diff Sump pump Monitor My parents have a cistern and a sump pump which would be useful to have some sort of water level monitoring. In the past, we would check the cistern level with a pressure gauge calibrated in inches of water. There was a rubber squeeze bulb which which would pressurize a plastic line which fed into the cistern, and the resulting level would be shown on the gauge. text/html 2014-11-13T22:37:16+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/7segdisplay?rev=1415918236&do=diff 7-segment display module [Working Display] Arduino library available on Github This was one of my first doublesided and surfacemount boards. I made this board using Eagle for layout and then I used BatchPCB to manufacture the board. The board operates correctly, however, if I were to revise it, I would use a larger SMT resistor than the 0402 size. The board will be controlled via I2C from a PIC microcontroller, initially for the pressure sensor and later for other projects. text/html 2014-11-13T18:50:14+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/50a5vpowersupply?rev=1415904614&do=diff 50 Amp 5 Volt Power Supply Need a 208.76 ohm, 1% resistor to set the 5V output. Right now I'm using a 500 ohm potentiometer. 200 ohms would output 5.02V. text/html 2014-11-13T18:50:14+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/barcodescanner?rev=1415904614&do=diff Motorola IR-200E Barcode Scanner [AAA Battery UPC] text/html 2014-11-13T22:12:24+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/dualpressuresensor?rev=1415916744&do=diff Barometric Pressure sensor Dual pressure sensor board [PIC18F1320 Datasheet] RX on pin 3 TX on pin 2 Power ON 98.97 kPa, 742.3 Torr ; 0814,0521 98.97 kPa, 742.3 Torr ; 0814,0521 98.97 kPa, 742.3 Torr ; 0814,0521 Reference Barometer - MPXAZ4115A text/html 2014-11-13T18:50:14+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/gps?rev=1415904614&do=diff GPS Haicom HI-406BT 19200bps, 8N1 Serial Data PinWireDescription Blue3Vpk-pk serial data Orange3.3V Green3.3V Red0V Referenced to Ground Haicom website * [HI-406BT Manual] GPS Receiver Modules * Lowrance LGC-12S - [Owner's manual] * Earthmate Hyperformance GPS Receiver - Rockwell binary output only text/html 2014-11-13T18:50:14+00:00 Anonymous (anonymous@undisclosed.example.com) https://www.photonicsguy.ca/projects/electronics/radiomodems?rev=1415904614&do=diff Radio Modems <http://lairdtech.stage.thomasnet.com/item/2-4-ghz-modules/ac-4424-transceivers/ac4424-200?&seo=110>